LS Motor

72blazer · 01-02-2016, 11:11 AM

Going to start looking for a 5.3 or 6.0. With or without a tranny would work. Good running condition without any holes blown through the block. As complete as possible. Willing to travel and pick up for the right deal to SA or Houston. Have cash and lots of stuff to trade. Or if you have any leads where I can get one, it'd be appreciated.

the_white_shadow · 01-02-2016, 08:56 PM

I have an '01 5.3l on an engine stand. 127k miles. From oil pan to intake. No flex plate. I do have the front drive accessories but aren't installed. Alt, PS pump, water pump, ac compressor (not sure if it works, but I have it). Have stock manifolds as well. No harness, ecm, trans. $600

I did have it drop off my fab table while I was attempting to get it back on the engine stand and dented the corner of the aluminum head. Should operate as normal.

Big4x4ride · 01-03-2016, 03:14 PM

I have a set of heads I believe if you end up needing them for any reason. Just need to make sure they are still there.

01-02-2016, 11:11 AM	#1
72blazer Wheels 4 Food Join Date: Oct 2004 Location: The Real South Texas Posts: 7,127	LS Motor Going to start looking for a 5.3 or 6.0. With or without a tranny would work. Good running condition without any holes blown through the block. As complete as possible. Willing to travel and pick up for the right deal to SA or Houston. Have cash and lots of stuff to trade. Or if you have any leads where I can get one, it'd be appreciated. __________________ The Web Wheeler's '72 Motorsport Syndicate:::Edinburg TX H&H Fabrication:::Amarillo TX Share Share this post on Digg Del.icio.us Technorati Twitter Facebook

01-02-2016, 08:56 PM	#2
the_white_shadow Wheelin MadMan Join Date: Feb 2012 Location: East Bernard Posts: 781	I have an '01 5.3l on an engine stand. 127k miles. From oil pan to intake. No flex plate. I do have the front drive accessories but aren't installed. Alt, PS pump, water pump, ac compressor (not sure if it works, but I have it). Have stock manifolds as well. No harness, ecm, trans. $600 I did have it drop off my fab table while I was attempting to get it back on the engine stand and dented the corner of the aluminum head. Should operate as normal. __________________ --Alex-- 1982 Toyota 4x4 - The dirt squirrel: LQ4/4l60e/Atlas 4.3, D60/14B w/ 5.13s, RCVs, Reids, 43" SX Stickies on Racelines, 3-link Front, 4-link Rear Share Share this post on Digg Del.icio.us Technorati Twitter Facebook

01-03-2016, 03:14 PM	#3
Big4x4ride Wheels 4 Food Join Date: Nov 2004 Location: Corpus Christi Posts: 6,733	I have a set of heads I believe if you end up needing them for any reason. Just need to make sure they are still there. Share Share this post on Digg Del.icio.us Technorati Twitter Facebook

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1 tons, 42's, h2's, LS motor	Big4x4ride	For Sale	36	09-14-2014 08:32 AM
LS Motor build	BlazerBoy	Gas\Diesel Engine & Transmission	36	05-12-2011 12:09 AM
Ls motor	Tiger Hays	Wanted	2	02-07-2011 08:53 AM
LS 1 motor	nhd	For Sale	0	04-27-2010 06:58 PM

Remove Advertisements Sponsored Links
Texas4x4 Advertisement

Wanted:

LS Motor